【hp】workstation i2000 Linux編

uname -a の結果 :

Linux localhost.localdomain 2.4.3-12smp #1 SMP Fri Jun 8 13:06:07 EDT 2001 ia64 unknown

cat /proc/cpuinfo の結果:

processor  : 0
vendor     : GenuineIntel
family     : IA-64
model      : Itanium
revision   : 6
archrev    : 0
features   : standard
cpu number : 0
cpu regs   : 4
cpu MHz    : 733.467020
itc MHz    : 733.467020
BogoMIPS   : 729.80

dmesg の結果: (MACアドレスは秘密)

Linux version 2.4.3-12smp (root@boris.devel.redhat.com) (gcc version 2.96 20000731 (Red Hat Linux 7.1 2.96-85)) #1 SMP Fri Jun 8 13:06:07 EDT 2001
EFI v1.02 by INTEL: SALsystab=0x3ff23630 ACPI=0x3ffd9f80 ACPI 2.0=0xe2000 MPS=0x3ffd0000 SMBIOS=0xf0020
CPU 0: mapping PAL code [0x3ff40000-0x3ff7b000) into [0xe00000003c000000-0xe000000040000000)
warning: skipping physical page 0
Initial ramdisk at: 0xe00000003efd3000 (696320 bytes)
SAL v3.00: oem=INTEL   MSL     REF     SAL     , product=
sal[0] - entry: pal_proc=0x3ff48010, sal_proc=0x3fe45c90
SAL: Platform features BusLock IRQ_Redirection 
CPU 0: 51 virtual and 44 physical address bits
ACPI 2.0 Root System Description Ptr at 0xe0000000000e2000
ACPI 2.0 XSDT at 0xe00000003ffd8030 (p=0x3ffd8030)
ACPI 2.0: Intel  W460GXBS 0.1
Acpi cfg:bind to Boot time Acpi OSD
ACPI: install SCI 9 handler pass
        :table FACP found
        :table APIC found
Lapic address set to 0xc0000000fee00000
ACPI 2.0 MADT: LOCAL APIC entry
ACPI 2.0 MADT: LOCAL APIC entry
ACPI 2.0 MADT: IO APIC entry
ACPI 2.0 MADT: LOCAL SAPIC
      CPU 0000:0000: available (BSP).
ACPI 2.0 MADT: LOCAL SAPIC
      CPU 0000:0001: disabled.
Acpi Cfg: get PRT pass
IOSAPIC: version 2.1, address 0xfec00000, IRQs 0x00-0x3f
ACPI 2.0 MADT: INT SOURCE Override
      1 CPUs available, 2 CPUs total
Acpi cfg:bind to Run time Acpi OSD
ia64_mca_init : begin
ia64_mca_init : registered mca rendezvous spinloop and wakeup mech.
ia64_mca_init : correctable mca vector setup done
ia64_mca_init : registered os mca handler with SAL
ia64_mca_init : os init handler at 44c6500
ia64_mca_init : registered os init handler with SAL
ia64_mca_init : platform-specific mca handling setup done
Mca related initialization done
On node 0 totalpages: 64657
zone(0): 64657 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: BOOT_IMAGE=vmlinuz-2.4.3-12smp root=/dev/sda4 ro
fpswa interface at 3f146010
CPU 0: base freq=133.357MHz, ITC ratio=11/2, ITC freq=733.467MHz
Console: colour VGA+ 80x25
Unexpected irq vector 0x0 on CPU 0!
Calibrating delay loop... 730.88 BogoMIPS
Placing software IO TLB between 0xe000000004a3c000 - 0xe000000008a3c000
Memory: 943520k/1034512k available (3912k code, 81808k reserved, 1248k data, 368k init)
perfmon: version 0.2 (sampling format v1)
perfmon: Interrupt vectored to 238
perfmon: 32 bits counters (max value 0xffffffff)
perfmon: 4 PMC/PMD pairs, 18 PMCs, 14 PMDs
Dentry-cache hash table entries: 65536 (order: 6, 1048576 bytes)
Buffer-cache hash table entries: 65536 (order: 5, 524288 bytes)
Page-cache hash table entries: 65536 (order: 6, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 6, 1048576 bytes)
VFS: Diskquotas version dquot_6.5.0 initialized
POSIX conformance testing by UNIFIX
SMP: starting up secondaries.
SMP: Bootstrap processor only.
SMP: Total of 1 processors activated (729.80 BogoMIPS).
PCI: Probing PCI hardware
PCI->APIC IRQ transform: (B0,I3,P3) -> 0x3b
PCI->APIC IRQ transform: (B0,I3,P1) -> 0x3a
PCI->APIC IRQ transform: (B0,I4,P0) -> 0x30
PCI->APIC IRQ transform: (B0,I5,P0) -> 0x31
PCI->APIC IRQ transform: (B1,I0,P0) -> 0x3c
PCI->APIC IRQ transform: (B1,I15,P0) -> 0x48
PCI->APIC IRQ transform: (B2,I15,P0) -> 0x51
PCI->APIC IRQ transform: (B3,I0,P0) -> 0x52
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
PAL Information Facility v0.4
EFI Variables Facility v0.03 2001-Apr-20
Starting kswapd v1.8
pty: 2048 Unix98 ptys configured
block: queued sectors max/low 626496kB/495424kB, 1856 slots per queue
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 19
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x1070-0x1077, BIOS settings: hda:pio, hdb:pio
hda: HITACHI DVD-ROM GD-7500, ATAPI CD/DVD-ROM drive
hdb: LS-120/240 00 UHD Floppy, ATAPI FLOPPY drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 34
hda: ATAPI 40X DVD-ROM drive, 512kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
hdb: No disk in drive
hdb: 234752kB, 262/32/56 CHS, 2995 kBps, 512 sector size, 1500 rpm
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 676kB freed
loop: loaded (max 8 devices)
Serial driver version 5.05a (2001-03-20) with MANY_PORTS SHARE_IRQ DETECT_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 44) is a 16550A
EFI Time Services Driver v0.3
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 928M
agpgart: Detected Intel 460GX chipset
agpgart: AGP aperture is 1024M @ 0x40000000
SCSI subsystem driver Revision: 1.00
request_module[scsi_hostadapter]: Root fs not mounted
request_module[scsi_hostadapter]: Root fs not mounted
md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md.c: sizeof(mdp_super_t) = 4096
autodetecting RAID arrays
autorun ...
... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 16384 buckets, 256Kbytes
TCP: Hash tables configured (established 131072 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem).
qla1x160: Supported Device Found VID=1077 DID=1216 SSVID=1077 SSDID=7
scsi(0): Determining if RISC is loaded...
scsi(0): Verifying chip...
scsi(0): Setup chip...
scsi(0): Configure NVRAM parameters...
[[[ qla1x160: 64 Bit PCI Addressing Enabled ]]]
scsi(0): Resetting SCSI BUS (0)
scsi(0): Resetting SCSI BUS (1)
scsi0 : QLogic QLA12160  PCI to SCSI Host Adapter: bus 1 device 0 irq 60
       Firmware version: 10.04.08, Driver version 3.24 Beta
  Vendor: SEAGATE   Model: ST318438LW        Rev: 0003
  Type:   Direct-Access                      ANSI SCSI revision: 03
scsi(0:0:1:0): Enabled tagged queuing, queue depth 255.
scsi(0:0:1:0): Synchronous tranfer at period 9, offset 24. 
scsi(0:0:1:0): Dual Transition enabled.
Attached scsi disk sda at scsi0, channel 0, id 1, lun 0
SCSI device sda: 38914049 512-byte hdwr sectors (19924 MB)
Partition check:
 sda: sda1 sda2 sda3 sda4 sda5
VFS: Mounted root (ext2 filesystem) readonly.
change_root: old root has d_count=3
Trying to unmount old root ... okay
Freeing unused kernel memory: 368kB freed
Adding Swap: 2096448k swap-space (priority -1)
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.251 $ time 13:16:20 Jun  8 2001
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0x1040, IRQ 59
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
usb.c: kmalloc IF e000000001117040, numif 1
usb.c: new device strings: Mfr=0, Product=2, SerialNumber=1
usb.c: USB device number 1 default language ID 0x0
Product: USB UHCI Root Hub
SerialNumber: 1040
hub.c: USB hub found
hub.c: 2 ports detected
hub.c: standalone hub
hub.c: ganged power switching
hub.c: global over-current protection
hub.c: Port indicators are not supported
hub.c: power on to power good time: 2ms
hub.c: hub controller current requirement: 0mA
hub.c: port removable status: RR
hub.c: local power source is good
hub.c: no over-current condition exists
hub.c: enabling power on all ports
usb.c: hub driver claimed interface e000000001117040
usb.c: kusbd: /sbin/hotplug add 1
hub.c: port 1 connection change
hub.c: port 1, portstatus 101, change 1, 12 Mb/s
hub.c: port 1, portstatus 103, change 0, 12 Mb/s
hub.c: USB new device connect on bus1/1, assigned device number 2
usb.c: kmalloc IF e000000001116e80, numif 1
usb.c: skipping descriptor 0x29
usb.c: skipped 1 class/vendor specific endpoint descriptors
usb.c: new device strings: Mfr=0, Product=0, SerialNumber=0
hub.c: USB hub found
hub.c: 4 ports detected
hub.c: standalone hub
hub.c: ganged power switching
hub.c: global over-current protection
hub.c: Port indicators are not supported
hub.c: power on to power good time: 100ms
hub.c: hub controller current requirement: 100mA
hub.c: port removable status: RRRR
hub.c: local power source is good
hub.c: no over-current condition exists
hub.c: enabling power on all ports
usb.c: hub driver claimed interface e000000001116e80
usb.c: kusbd: /sbin/hotplug add 2
ip_conntrack (4036 buckets, 32288 max)
eepro100.c:v1.09j-t 9/29/99 Donald Becker http://cesdis.gsfc.nasa.gov/linux/drivers/eepro100.html
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin  and others
eth0: Intel Corporation 82557 [Ethernet Pro 100], 00:00:00:00:00:00, I/O at 0x1000, IRQ 49.
  Receiver lock-up bug exists -- enabling work-around.
  Board assembly 731296-005, Physical connectors present: RJ45
  Primary interface chip i82555 PHY #1.
  General self-test: passed.
  Serial sub-system self-test: passed.
  Internal registers self-test: passed.
  ROM checksum self-test: passed (0x04f4518b).
  Receiver lock-up workaround activated.

おまけ: NetscapeNavigator 4.77の返すUSER-AGENT:

HTTP_USER_AGENT=Mozilla/4.77 [ja/[Vine,RedHat]] (X11; U; Linux 2.4.3-12smp i686)